Yes, adding the drywall onto the basement ceiling joists is possible, but experts do not recommend it. The basement ceiling consists of pipes, ducts, and wires utilized in the house. When the time comes that you require these elements, you will have to cut into the ceiling, making an even bigger mess.
Moreover, do you have to use screws to attach ceiling drywall?
No, you can use drywass nails, but screws hold better and are less likely to show a pop out later. Just be careful using nails ir screws not to break the surface of the paper. Using a glue on the ceiling joist is also a very good idea. Especially if there is a floor level above the one you’re hanging, or if there is a hot attic above.
How to hang drywall on a ceiling?
Hang the Top Sheet of Drywall. Lift the top wall sheet, holding it tight against the ceiling, and tack it into place with nails. Pro tip: This sheet should be pushed tight against the ceiling before fastening. Never break joints at the edge of a window or door.
You may be thinking “How do you put drywall on the ceiling?”
The general rule for hanging ceiling drywall is to install the largest panels you can handle. Using a Lift. To save your neck, arms and back, use a drywall lift when installing panels on the ceiling.
Therefore, the first thing to consider when laying-out drywall is to keep the bound edges paired with bound edges and the drywall butts paired with drywall butts. To describe this point we will speak specifically about walls however the principles carry over to ceilings and soffits.
Do drywall edges have to meet on a joist?
No, it would not be okay. Drywall needs to be attached at its edges. The standard approach is to build a pont to attach the edge of the drywall. Generally, you screw a dummy joist at the edge of the wall.
Another frequent inquiry is “Should drywall edges be aligned?”.
Lee has over two decades of hands-on experience remodeling, fixing, and improving homes, and has been providing home improvement advice for over 12 years. Hanging and aligning drywall perfectly can be tough. Whenever possible, it is preferable to align the two tapered (or angled) edges of adjoining sheets of drywall.
Another frequent inquiry is “Do drywall seams need to be centered?”.
Ideally you want to make sure that the drywall seams are centered on a stud frame in order to secure it adequately to the structure. In situations where drywall is not able to be mounted to studs or other structural members, failure in the joint is likely.
This is because the butted seam is attached along a single stud or joist which is typically only 1 ½ inches wide. The screws are often angled somewhat and are too close to the drywall edge which damages the drywall core and weakens the attachment. Edge and as a result drywall core was damaged.
What happens if you put drywall on Studs?
Seams that land directly on a stud have less cross sheet holding power and the chances of seams popping or cracking is increased. For this reason, when hanging drywall over wood studs, you should almost always lay them out perpendicular to the direction of the studs.
Are drywall seams on studs?
Drywall Is Not on a Stud All edges of all sheets of drywall must land on a solid surface such as a stud. A hanging drywall edge may work in the short-term, but in the long-term it can result in cracks and other serious wall issues.
Another frequently asked query is “How many drywall edges should be on Studs?”.
7 The edges of your drywall pieces must be on studs – at least two of them and preferentially all four. (some drywall guys will vastly disagree with needing 4 so not trying to start a war) But two is a must. Your drywall should end on stud or be butted up in the center with another piece of drywall.
What are the long edges of drywall panels?
The long edges of drywall panels are tapered slightly to accommodate joint tape and compound. The panel ends are cut square and finished smooth with the gypsum core exposed, and are thus un-tapered.
What is the edgedrywall?
Drywall is designed so that the edges are thinner than the rest of the sheet. This is to allow for the application of thin layers of drywall mud and taping between the joints without creating a build-up.